- This system can be used for filtering, finishing and bottling, making the transition between these steps seamless.
- The pans are handcrafted out of 22ga mirror finish stainless steel (which is food grade and rust resistant).
- All pans are handcrafted and our TIG welds come with a lifetime guarantee.
- The syrup pan has built-in full-length handles on each side.
- The standard draw-off valve is solid stainless steel (NOT nickle plated). A drip-resistant Tomlinson Valve is also available as an upgrade.
HOW TO USE THIS SYSTEM FOR FILTERING:
- Place the main pan on a sturdy, level surface. Insert the Filter Tray on top of the main pan.
- Place a set of Flat Filters in the Filter Tray with the thicker, main filter on the bottom and the prefilters on top. (See “How to use Flat Filters” for more information)
- Make sure the draw-off valve and thermometer are securely threaded into the front of the main pan. We recommend using Teflon Plumbers Tape (not included) on all threaded connections to prevent binding and to ensure a tighter seal.
- Pour hot syrup into the Filter Tray and let it drain into the main pan below. Remove the top prefilter as necessary as described in the “How to use Flat Filters” section below.
HOW TO USE FLAT FILTERS:
- First, cut your flat main flat filter (usually made out of Orlon) and flat prefilter material to 18″ x 18″ square. (If purchasing a flat filter set from us, you can skip this step. We will precut the filters for you. Our sets come with one Orlon base filter and 5 prefilters.)
- Place your base filter (usually made from Orlon) at the bottom of the filter tray and then place a stack of about five prefilters on top of it. Note that the filters need to overhang the edges of the filter tray to make it easier to grab and adjust them later on. You may choose to use a clothespin or a binder clip to clip the filters together in the corners. This will help prevent the edges of the filter papers from falling over into the tray.
- Pour your syrup into the Filter Tray while it is HOT. (Many people will filter their syrup directly off of their evaporator.)
- When the top prefilter clogs with sediment, shimmy it out and the syrup will flow through again. When the next prefilter clogs, shimmy out that prefilter and so on. The prefilter material is composite and can be used over and over. They rinse very well. Never run your syrup directly into the base filter unless you have very little to filter.
HOW TO USE THIS SYSTEM FOR BOTTLING
- After filtering your syrup as described above, cover the pan with the lid so that no evaporation can occur.
- Perform a density test to ensure the syrup is suitable for bottling. The density should be between 66º – 66.9º BRIX. We recommend using a Murphy Cup and hydrometer to easily and quickly get an accurate density reading.
- If your syrup is too dense, crystals will form at the bottom of your containers. Slowly stir in a small amount of distilled water or sap until perfect density is achieved. Conversely, if your syrup is not dense enough, you will need to use your Steam Tray to heat the syrup and do more evaporating. Remove the lid and filter tray and set them aside. Then follow the instructions for using your particular type of steam tray below. (electric vs gas-fired.) The steam will evenly heat the bottom of your main pan, so you can avoid the hot spots which can generate sugar sand.
- Once you have achieved proper density, bring the syrup temperature to 180ºF. Monitor syrup temperature using the thermometer on the front of the main pan.
- Wearing rubber gloves to protect your hands from hot syrup, use the draw-off valve to fill your clean, food-safe bottles/cans with syrup. Leave a small amount of air at the top of each container. Shake each container and lay on its side so that the heat neutralizes any bacteria that may have been present.
USING A STEAM TRAY WITH GAS-FIRED BURNER:
- Place the Gas Burner and Stand on a sturdy, level surface.
- Fill the Steam Tray with approx 1 – 2″ of water and set it on top of the Gas Burner and Stand. The notched edge of the Steam Tray should be facing you.
- Place the Main Pan on top of the Steam Tray so that the draw-off valve is facing you. (The draw-off valve should rest inside the notch on the Steam Tray.) If you have not done so already, fill the main pan with syrup, filtering if necessary.
- Light the gas burner and allow time for the steam from the Steam Tray to heat your syrup to your desired temperature. Monitor your syrup’s temperature using the thermometer on the front of the main pan. Note that you should NOT see any significant amount steam escaping from the Steam Tray. If you do, make sure your main pan is sitting on the Steam Tray properly. If a small amount of steam is still escaping, you may need to add water to the Steam Tray after a period of time. NEVER heat the Steam Tray when there isn’t water in it as this could cause the Steam Tray to warp.
USING A STEAM TRAY WITH ELECTRIC ELEMENT:
- Using Teflon plumbers tape, thread the electric element into the fitting on the Steam Tray. (The tape prevents binding and ensures a tighter seal.)
- Fill the Steam Tray so that the electric element is FULLY immersed. If not fully immersed, corosion may occur while the element is hot.
- Set the Steam Tray on a sturdy, level surface so that the side with the notched edge is facing you. Then place the main pan on top of the Steam Tray so that the draw-off valve is resting in the notch on the steam tray. If you have not done so already, fill the main pan with syrup, filtering if necessary.
- Plug in the electric element. Allow time for the steam from the Steam Tray to heat your syrup to your desired temperature. Monitor your syrup’s temperature using the thermometer on the front of the main pan. Note that you should NOT see any significant amount steam escaping from the Steam Tray. If you do, make sure the main pan is sitting on the Steam Tray properly. If a very small amount of steam is still escaping, you may need to add water to the Steam Tray after a period of time. NEVER heat the Steam Tray when there isn’t water in it as this could cause the Steam Tray to warp and will cause damage to the element.
NEVER heat a pan that doesn’t have any liquid in it as this can cause warping. Never place your face or other body parts in steam. Remember that equipment and syrup will get HOT. Wear protective gloves, goggles, etc to prevent burns.